Pooling water in a shower is the most common post-renovation complaint, and it is almost never a tiling problem. It is a set-out problem, decided weeks earlier when the waste position and the falls were established.
This guide explains how bathroom drainage geometry works — what a fall is, how it is created, the difference between square and linear wastes, and the details that separate a floor that drains completely from one that holds a puddle for an hour after every shower.
It pairs with bathroom plumbing and drainage explained. More guides are in the free renovation advice hub.
Why does my shower floor hold water?
Because the fall toward the waste is insufficient, uneven, or interrupted. Australian requirements set minimum gradients for shower floors and the surrounding bathroom floor, and those falls are created in the screed beneath the waterproofing — not by the tiler adjusting adhesive thickness. Large-format tiles on a floor that must fall in several directions, a waste set too high, or a screed laid without proper set-out are the usual causes.
What a Fall Actually Is
A fall is a deliberate gradient built into the floor so water runs toward the waste under gravity. It is expressed as a ratio — a drop of a certain amount over a horizontal distance.
Australian Standards set minimum gradients for shower areas and for the general bathroom floor, with the shower requiring the steeper fall. The floor also needs to be graded so that water cannot travel away from the waste toward a doorway.
- the shower area falls more steeply than the rest of the room
- the general floor falls gently back toward the waste, not toward the door
- falls are formed in the screed, before waterproofing is applied
- waterproofing follows the screed profile, so it drains too
- the tile bed maintains the profile rather than correcting it
- the waste must be the lowest point of every plane feeding it
Too much fall is also a problem: an aggressive gradient makes large tiles difficult to lay flat, and a shower floor that feels noticeably sloped underfoot is uncomfortable and can be a trip risk.
Square Wastes vs Linear Drains
The waste type determines how many directions the floor has to fall in, which in turn determines what tile sizes are practical.
Centre square waste
The traditional approach. The floor falls from all four sides toward a central point, creating four planes. It is economical and reliable, but it forces small tiles or mosaics in the shower because a large tile cannot follow four intersecting planes without lipping.
Linear channel drain
A long slot drain set against one wall or at the shower entry. The floor falls in a single direction only, which means large-format tiles can run through the shower uninterrupted. It is the reason contemporary bathrooms can use 600mm tiles in a wet area.
- linear drains cost more in both the product and the installation
- tile-insert grates let the floor tile continue across the drain visually
- channel position at the wall keeps the entry edge level for a step-free shower
- square wastes remain the sensible choice with mosaic or small-format floors
- either type must be set to the correct height before screeding
- hair and debris access for cleaning differs between the two — check the removable insert
The Screed Is Where It Is Won or Lost
The screed is the sand-cement bed that establishes the finished floor profile. It is invisible in the completed room and it determines almost everything about how the floor performs.
- the waste height is set first, and everything is built to it
- the substrate is prepared and bonded so the screed does not delaminate
- the screed is laid to string lines or set-out marks, not by eye
- falls are checked with a level before the screed cures
- the screed must cure before waterproofing can be applied
- any hobs or shower kerbs are formed at the same stage
This is one of the stages where rushing shows up years later. A screed that is allowed to cure properly before waterproofing is a small delay in the program and a large factor in the life of the room — see what to expect during a bathroom renovation.
Wet Rooms and Step-Free Showers
Removing the shower hob to create a level entry changes the drainage problem entirely, because there is no longer a physical barrier holding water in the shower.
- the falls have to be correct, because nothing else contains the water
- a linear drain at the far wall or across the entry is usually required
- a slight recess or gradient change at the entry helps define the wet zone
- the waterproofing membrane must extend further across the floor
- a secondary floor waste in the main bathroom area is common practice
- the substrate may need to be recessed to accommodate the drainage build-up
Level-entry showers are the single most valuable ageing-in-place feature in a bathroom, and far cheaper to build now than to retrofit — see accessible and ageing-in-place bathrooms.
Common Problems and Their Causes
Diagnosing a drainage complaint is usually straightforward once you know where to look.
- water pooling in one corner — insufficient fall on that plane, or a dip in the screed
- water sitting around the grate — the waste was set slightly too high
- water travelling toward the door — the general floor falls the wrong way
- slow draining — a blockage, or a waste undersized for the shower flow rate
- gurgling or odour — a trap issue or venting problem rather than a fall problem
- lipping tiles in the shower — large tiles used on a four-plane fall
The uncomfortable reality is that most of these cannot be corrected without removing the tiles, the waterproofing and the screed. That is why the set-out stage deserves attention while it is still cheap to influence.
Checks Worth Making During the Build
You do not need to be a tradesperson to make a few useful observations at the right moments.
- ask where the waste will sit and in which direction the floor will fall
- confirm whether a square or linear waste suits the tile size you have chosen
- look at the screed before waterproofing — the fall should be visible to the eye
- ask whether a flood test will be carried out after the membrane cures
- after tiling, tip a jug of water on the floor and watch where it goes
- check the grate insert is removable for cleaning
A simple water test at practical completion, before final payment, takes two minutes and is the most direct evidence you will ever have that the floor works.
Frequently Asked Questions
Australian Standards set minimum gradients for shower areas and a gentler minimum for the surrounding bathroom floor, with the shower requiring the steeper fall. Your contractor should be building to the current standard, and it is a reasonable question to ask before screeding.
Rarely. Because falls are formed in the screed beneath the waterproofing membrane, correcting them means removing the tiles, the membrane and the screed. Occasionally a waste can be adjusted, but a genuine fall problem is a rebuild of the floor.
They are better for large-format tiles and level-entry showers because the floor only falls in one direction. A correctly installed square waste drains just as effectively with smaller tiles, at lower cost. The choice should follow the tile and the shower design.
It is common and often required depending on the layout, and it is strongly advisable in a wet room or level-entry design. It also provides a path for water if a fixture leaks or overflows.
That is usually a trap that has dried out or a venting issue rather than a drainage-fall problem. A rarely used floor waste can lose its water seal; running water into it periodically usually resolves it, and persistent odour warrants a plumber.
Sometimes, but it depends on the slab or floor structure and the position of the drainage line below. On a concrete slab it may require core drilling and can be costly, which is why waste positions are one of the earliest layout decisions.
Related advice
More free guidance for Gold Coast and Brisbane homeowners.
Bathroom Plumbing and Drainage ExplainedRough-in, pipework and why moving a toilet costs more.
Accessible and Ageing-in-Place BathroomsLevel-entry showers and the details that make them work.
Why Bathroom Waterproofing MattersThe membrane that sits directly on top of the screed.
Floors That Actually Drain
VN Bathrooms sets waste heights and falls before screeding, and water-tests every completed floor on Gold Coast and Brisbane renovations.
- QBCC Licensed #15521533
- Fixed-Price Written Quotes
- 7-Year Workmanship Warranty
Prefer to talk it through? Call or send a text message to 0434 242 045.