A bathroom with beautiful tiles and poor lighting looks flat. A bathroom with modest finishes and considered lighting looks resolved. Yet lighting is routinely the last thing discussed, usually as a question about how many downlights to put in the ceiling.
The number of downlights is close to the least important part of the decision. What matters is where light comes from, what it is doing, and whether the person standing at the mirror is lit from the front rather than from directly overhead.
This guide explains how lighting and electrical work is planned in Gold Coast and Brisbane bathroom renovations. For the rest of the selection process, see our free renovation advice hub.
How should bathroom lighting be planned?
Plan in three layers: general ceiling light for the whole room, task light at the mirror positioned to light the face from the front, and accent or feature light such as a niche strip or under-vanity glow. Keep every fitting at the same colour temperature, put the mirror light on its own switch, and confirm all positions before electrical rough-in. Wet-area requirements are set by AS/NZS 3000 and must be applied by a licensed electrician.
All electrical work in a bathroom must be carried out by a licensed electrician. Zone requirements and fitting ratings depend on your specific layout and must be confirmed on site.
Why Lighting Is an Early Decision, Not a Late One
Electrical rough-in happens while the walls and ceiling are open, immediately after demolition and framing. Everything that needs a cable has to be decided by then.
- downlight and feature light positions, set out against the tile and fixture layout
- cabling for a backlit or demisting mirror
- switch positions, including whether the mirror light is separately switched
- the exhaust fan location and the route its ducting will take
- heated towel rail circuit and its exact wall position
- underfloor heating, which must be installed before screeding and tiling
- power points near the vanity in compliant positions
Adding any of these afterwards means opening a finished, waterproofed and tiled surface — which is why they belong in the design conversation alongside layout.
The Three Layers of Bathroom Lighting
Professional lighting design in any room works in layers. A bathroom needs all three, and most poorly lit bathrooms only have one.
1. General light
Even illumination across the room so nothing sits in shadow. Usually ceiling downlights, positioned to wash the walls rather than to form a rigid grid. Light bouncing off a pale tiled wall does far more work than an extra fitting in the middle of the ceiling.
2. Task light
Light for shaving, applying makeup and looking at your own face honestly. It must come from in front of the user, not from above. This is the single biggest improvement most bathrooms can make.
3. Accent light
The layer that makes a bathroom feel designed — a strip inside a shower niche, a soft glow beneath a wall-hung vanity, or a discreet fitting washing a feature tile. It also doubles as gentle night lighting without switching on the main circuit.
Switching matters as much as fittings
Three layers on one switch is effectively one layer. Separating the mirror light, and putting accent lighting on its own control, is what makes the layering usable day to day.
Mirror lighting, an accessible power point and a heated towel rail all need cabling set out before the wall is lined.Getting the Mirror Light Right
A single downlight above the mirror lights the top of the head and casts shadows under the eyes, nose and chin — the worst possible arrangement for the one task the mirror exists for.
- backlit LED mirror: soft, even, and the most common modern solution
- vertical fittings either side of the mirror: excellent, symmetrical face lighting
- an illuminated shaving cabinet: combines storage with front-facing light
- a wall light above and forward of the mirror, angled towards the face rather than the wall
- avoid relying on a ceiling downlight positioned directly overhead
- consider a demister pad if the mirror fogs badly in a humid bathroom
Mirror fogging is usually a symptom of insufficient extraction rather than a mirror problem — which is covered in our guide to bathroom ventilation and mould prevention.
Colour Temperature, Brightness and Dimming
Colour temperature describes whether light appears warm or cool. Warmer light feels relaxing but can shift how colours read at the mirror; cooler light feels crisp but can tip into clinical. Neutral white is the usual compromise in a bathroom.
- keep every fitting in the room at the same colour temperature — mismatches are very visible
- check the colour rendering quality if accurate colour at the mirror matters to you
- pale tiles reflect more light, so an identical fitting count reads brighter
- dimming needs compatible fittings and a compatible dimmer, specified upfront
- an ensuite benefits most from dimming, for low-level use at night
- accent lighting on its own switch can replace a night light entirely
Wet Areas, Zones and Electrical Safety
Bathrooms are classified into zones based on proximity to water, and the wiring rules (AS/NZS 3000) set what may be installed in each. This determines which fittings can go inside a shower, where a power point may sit relative to a basin or bath, and what ingress protection rating a fitting must have.
- all bathroom electrical work must be performed by a licensed electrician
- fittings must carry an appropriate rating for the zone they are installed in
- power point positions relative to baths, basins and showers are prescribed, not optional
- circuits require appropriate protection, which your electrician will specify
- an electrical safety certificate should be provided for the completed work
- in apartments, additional body corporate requirements may apply
VN Bathrooms coordinates licensed electrical trades as part of a complete bathroom renovation, so compliance is handled within the build rather than left to the homeowner to arrange.
Exhaust Fans, Heat Lamps and Combination Units
Extraction is an electrical decision with a much bigger impact on the bathroom's long-term condition than any light fitting. In a subtropical climate, moving humid air out of the room is what protects grout, silicone, cabinetry and paint.
- a dedicated high-performance exhaust fan generally outperforms a three-in-one combination unit
- extraction must discharge outside the building, not into the roof space
- duct runs should be as short and straight as practical
- position the fan to draw air across the room from the door towards the shower
- a timer or humidity sensor keeps the fan running after the room is vacated
- heat lamps are optional in South East Queensland and consume ceiling space
Power Points, Towel Rails and Underfloor Heating
Power points
At least one accessible point near the vanity for hair dryers, shavers and electric toothbrushes is close to essential. Position is governed by the wiring rules, so it should be planned rather than added at the end. Some shaving cabinets include internal points, which keeps benchtops clear.
Heated towel rails
More useful on the Gold Coast than heat lamps, because they dry towels in humid conditions. Hardwired rails need a cable at the exact mounting position, so the rail must be selected before rough-in. Adding a timer avoids leaving it running all day.
Underfloor heating
Less common in Queensland than in cooler states, but occasionally requested in ensuites. It must be installed under the screed before tiling, which means the decision cannot be deferred.
Working With Natural Light in Queensland Homes
Natural light is the cheapest lighting upgrade available, and many South East Queensland bathrooms have more of it available than they use. Privacy is usually the limiting factor rather than the opening itself.
- obscure or frosted glazing keeps light while removing sightlines
- louvre windows provide light and passive ventilation together
- a high-level window above the shower brings in light without exposure
- skylights or tubular daylights suit internal bathrooms with no external wall
- pale wall tiles multiply whatever daylight enters the room
- remember that a bathroom is used before dawn and after dark, so artificial layers still matter
Window position also interacts with layout — see bathroom layout and space planning for how the two decisions are made together.
Lighting Mistakes We See Most Often
- one central downlight doing every job in the room
- the only mirror light positioned directly above the user's head
- all lighting on a single switch, so the layers cannot be used independently
- mixing warm and cool fittings in the same room
- no power point within reach of the vanity
- an undersized exhaust fan, or ducting discharging into the roof space
- downlights set out on a grid that ignores where the vanity and shower actually sit
- deciding on a backlit mirror after the wall has already been lined and tiled
These sit alongside the broader pitfalls in bathroom renovation mistakes to avoid.
Frequently Asked Questions About Bathroom Lighting
It depends on ceiling height, room size, tile colour and the beam angle of the fittings, so there is no single number. A more reliable approach is to plan the layers first — general light, task light at the mirror and light inside the shower — and let the fitting count follow from that.
Neutral white is a common choice because it renders skin tones reasonably and still feels clean. Warmer light feels more relaxing but can distort colour at the mirror, while very cool light can feel clinical. Keeping every fitting in the room at the same temperature matters more than the exact figure.
Yes, provided the fitting is rated for that location and installed by a licensed electrician in accordance with the wiring rules. Shower zones have specific requirements under AS/NZS 3000, and your electrician will confirm what is permitted for your ceiling and layout.
They provide soft, even light around the face and remove the harsh shadowing created by a single downlight above the head. They need cabling planned before the wall is lined, and quality varies — check the light output, whether it is dimmable and the demister function if that matters to you.
Power point placement in wet areas is governed by AS/NZS 3000, which sets minimum distances from baths, basins and showers. A licensed electrician determines compliant positions on site. Planning at least one accessible point near the vanity during design avoids adding it awkwardly later.
Many South East Queensland households find heat lamps unnecessary given the climate, and prefer a dedicated high-quality exhaust fan instead. Combination three-in-one units save ceiling space but often compromise on extraction performance compared with a standalone fan.
Dimming is popular for evening use, particularly in an ensuite. It requires compatible fittings and a compatible dimmer, so it should be specified upfront rather than retrofitted, and it works best when the mirror light is on its own switch.
Before rough-in, while the walls and ceiling are open. Switch positions, mirror cabling, exhaust ducting, heated towel rail circuits and underfloor heating all have to be installed at that stage, so late changes usually mean reopening lined or waterproofed surfaces.
Related advice
More free guidance for Gold Coast and Brisbane homeowners.
Bathroom Ventilation and Mould PreventionExhaust performance, condensation and keeping surfaces mould-free.
Bathroom Layout and Space PlanningClearances, wet zones and how to make a compact bathroom work.
Choosing Bathroom Tapware and FixturesFinishes, vanities, basins and how PC item allowances work.
Plan Lighting Before the Walls Close
VN Bathrooms coordinates licensed electrical trades alongside layout, waterproofing and tiling for Gold Coast and Brisbane bathrooms — so lighting, extraction and power are resolved before rough-in, not improvised afterwards.
- QBCC Licensed #15521533
- Fixed-Price Written Quotes
- 7-Year Workmanship Warranty
Prefer to talk it through? Call or send a text message to 0434 242 045.